Yaskawa Yaskawa Sigma-7 SERVOPACK (SGD7S analog/pulse; SGD7W/SGD7C per hardware-option manual)
- A.020 — A.020 — Parameter Checksum Error
- A.021 — A.021 — Parameter Format Error
- A.022 — A.022 — System Checksum Error
- A.024 — A.024 — System Alarm
- A.025 — A.025 — System Alarm
- A.030 — A.030 — Main Circuit Detector Error
- A.040 — A.040 — Parameter Setting Error
- A.041 — A.041 — Encoder Output Pulse Setting Error
- A.042 — A.042 — Parameter Combination Error
- A.044 — A.044 — Semi-Closed/Fully-Closed Loop Control Parameter Setting Error
- A.050 — A.050 — Combination Error
- A.051 — A.051 — Unsupported Device Alarm
- A.070 — A.070 — Motor Type Change Detected
- A.080 — A.080 — Linear Encoder Pitch Setting Error
- A.100 — A.100 — Overcurrent Detected
- A.101 — A.101 — Motor Overcurrent Detected
- A.300 — A.300 — Regeneration Error
- A.320 — A.320 — Regenerative Overload
- A.330 — A.330 — Main Circuit Power Supply Wiring Error
- A.400 — A.400 — Overvoltage
- A.410 — A.410 — Undervoltage
- A.510 — A.510 — Overspeed
- A.511 — A.511 — Encoder Output Pulse Overspeed
- A.520 — A.520 — Vibration Alarm
- A.521 — A.521 — Autotuning Alarm
- A.550 — A.550 — Maximum Speed Setting Error
- A.710 — A.710 — Instantaneous Overload
- A.720 — A.720 — Continuous Overload
- A.730 — A.730 — Dynamic Brake Overload
- A.731 — A.731 — Dynamic Brake Overload
- A.740 — A.740 — Inrush Current Limiting Resistor Overload
- A.7A1 — A.7A1 — Internal Temperature Error 1 (Control Board Temperature Error)
- A.7A2 — A.7A2 — Internal Temperature Error 2 (Power Board Temperature Error)
- A.7A3 — A.7A3 — Internal Temperature Sensor Error
- A.810 — A.810 — Encoder Backup Alarm
- A.820 — A.820 — Encoder Checksum Alarm
- A.830 — A.830 — Encoder Battery Alarm
- A.840 — A.840 — Encoder Data Alarm
- A.850 — A.850 — Encoder Overspeed
- A.860 — A.860 — Encoder Overheated
- A.861 — A.861 — Motor Overheated
- A.862 — A.862 — Overheat Alarm
- A.890 — A.890 — Encoder Scale Error
- A.891 — A.891 — Encoder Module Error
- A.8A0 — A.8A0 — External Encoder Error
- A.8A1 — A.8A1 — External Encoder Module Error
- A.8A2 — A.8A2 — External Incremental Encoder Sensor Error
- A.8A3 — A.8A3 — External Absolute Encoder Position Error
- A.8A5 — A.8A5 — External Encoder Overspeed
- A.8A6 — A.8A6 — External Encoder Overheated
- A.C10 — A.C10 — Servomotor Out of Control
- A.C20 — A.C20 — Phase Detection Error
- A.C21 — A.C21 — Polarity Sensor Error
- A.C22 — A.C22 — Phase Information
- A.C50 — A.C50 — Polarity Detection Failure
- A.C51 — A.C51 — Overtravel Detected during Polarity Detection
- A.C52 — A.C52 — Polarity Detection Not Completed
- A.C53 — A.C53 — Out of Range of Motion for Polarity Detection
- A.C54 — A.C54 — Polarity Detection Failure 2
- A.C80 — A.C80 — Multiturn Limit Setting Error
- A.C90 — A.C90 — Encoder Communications Error
- A.C91 — A.C91 — Encoder Communications Position Data Acceleration Rate Error
- A.C92 — A.C92 — Encoder Communications Timer Error
- A.CA0 — A.CA0 — Encoder Parameter Error
- A.CC0 — A.CC0 — Multiturn Limit Disagreement
- A.CF1 — A.CF1 — Reception Failed Error in Feedback Option Module Communications
- A.CF2 — A.CF2 — Timer Stopped Error in Feedback Option Module Communications
- A.E71 — A.E71 — Safety Option Module Detection Failure
- A.E72 — A.E72 — Feedback Option Module Detection Failure
- A.E74 — A.E74 — Unsupported Safety Option Module
- A.EC8 — A.EC8 — Gate Drive Error 1
- A.EC9 — A.EC9 — Gate Drive Error 2
- A.F10 — A.F10 — Power Supply Line Open Phase
- A.900 — A.900 — Position Deviation Overflow
- A.901 — A.901 — Position Deviation Overflow Alarm at Servo ON
- A.910 — A.910 — Overload
- A.911 — A.911 — Vibration
- A.912 — A.912 — Internal Temperature Warning 1 (Control Board Temperature Error)
- A.913 — A.913 — Internal Temperature Warning 2 (Power Board Temperature Error)
- A.920 — A.920 — Regenerative Overload
- A.921 — A.921 — Dynamic Brake Overload
- A.923 — A.923 — SERVOPACK Built-in Fan Stopped
- A.930 — A.930 — Absolute Encoder Battery Error
- A.93B — A.93B — Overheat Warning
- A.941 — A.941 — Change of Parameters Requires Restart
- A.942 — A.942 — Speed Ripple Compensation Information Disagreement
- A.971 — A.971 — Undervoltage
- A.9A0 — A.9A0 — Overtravel